New CCT Help?!?! Rattle

CBR Forum Classifieds News Photo Gallery Search Member List Timeslips Contact Sponsors Register Login

New CCT Help?!?! Rattle

Printable Version

CBR >> Past CBR Models >> CBR 600F2 >> New CCT Help?!?! Rattle

Page: [1]

Message

<< Older Topic Newer Topic >>

New CCT Help?!?! Rattle - 6/20/2006 10:08:21 PM

suream

Posts: 41
Joined: 4/23/2006
Status: offline

Well I just installed a new manual CCT on my 91 f2. It sounds great when at idle but the minute I twist the throttle just a little the noise begins. It is a loud rattle noise. I tried adjusting the cct and get no change in the sound. Also I can tell when I start to get too tight on the chain, I hear the cams start to stress a little so I back off on the tensioner. Any suggestions that might help me out a little.

Thanks

< Message edited by suream -- 7/14/2006 2:53:53 AM >

Post #: 1

RE: New CCT Help?!?! - 6/21/2006 10:42:29 AM

mikequinn

Posts: 294
Joined: 3/30/2006
From: UK.
Status: offline

If you put a new CCT on that should cure the problem, although some new CCTs have been known to be faulty, see if you can try another to cure the rattle, if that dosent cure it you may have another problem with the engine sorry to say,
it could also be that the cam chain guides have worn out, if your putting too much tension on these it wont help matters,

(in reply to suream)

Post #: 2

RE: New CCT Help?!?! - 6/21/2006 11:35:40 AM

suream

Posts: 41
Joined: 4/23/2006
Status: offline

So the guides could cause a loud rattle? That may be just about the only thing. It sounds like something is slapping against the inside of the engine.

(in reply to suream)

Post #: 3

RE: New CCT Help?!?! - 6/22/2006 1:21:51 AM

suream

Posts: 41
Joined: 4/23/2006
Status: offline

Found the problem! Pulled the cams and the first intake valve lifter I pulled had a piece of metal under it. It was the valve cotter. This keeps the valve in place with the springs. well the valve was just hitting randomly and causing the rattle. I have to pull the head and inspect the valve and install a new cotter.

(in reply to suream)

Post #: 4

RE: New CCT Help?!?! - 6/22/2006 5:29:25 AM

mikequinn

Posts: 294
Joined: 3/30/2006
From: UK.
Status: offline

Glad to hear you found something that might be causing the rattle, reply back to post and let us know if that cured your problem

(in reply to suream)

Post #: 5

RE: New CCT Help?!?! - 7/11/2006 4:29:33 PM

suream

Posts: 41
Joined: 4/23/2006
Status: offline

Well, I have pulled the head and installed the new valve cotter (keeper). I have also checked the valve clearances and set the timeing. Now I have it all back together and waiting to start it. Just have to let a few places that have gasket sealant to dry. I will keep you posted as to how it goes.

(in reply to suream)

Post #: 6

RE: New CCT Help?!?! - 7/11/2006 6:54:32 PM

suream

Posts: 41
Joined: 4/23/2006
Status: offline

It runs! Started right up and no noise at all... she runs fine!

(in reply to suream)

Post #: 7

RE: New CCT Help?!?! - 7/12/2006 5:59:58 AM

mikequinn

Posts: 294
Joined: 3/30/2006
From: UK.
Status: offline

Glad to hear you sorted the problem with your bike, have fun riding it and stay safe
Best of luck.