98 plastics on a 92 F2

Printable Version

CBR >> Past CBR Models >> CBR 600F2 >> 98 plastics on a 92 F2

Page: [1]

Login Message << Older Topic   Newer Topic >>

98 plastics on a 92 F2 - 7/2/2006 9:28:44 PM    spencerjw Posts: 113 Joined: 6/25/2006 Status: offline Ok, so I had noticed last week that someone in their sig file mentioned they had a 92 F2 (or was it a 91) but had 98 plastics on it. Is this an easy conversion or did it take a lot of work to get it to fit correctly? I like the 92 plastics jsut fine but since I need tog et new ones and I have always wanted a 98 look I figured maybe that conversion would be just wnat i needed. What's did it take? How much did it cost (un-painted) Was it worth the work (if there was a lot of it). Thanks! _____________________________ Spencer '92 Honda CBR 600 F2 Post #: 1

RE: 98 plastics on a 92 F2 - 7/2/2006 11:00:04 PM    Nick I.   Posts: 181 Joined: 3/30/2006 From: Delco Pa. Status: offline They were on the bike when I bought it, they fit fine though. not sure if the mirror stay is from a 98 or not though. _____________________________ 1993 F2 - 1998 Plastic. Sold! The Replacement 2003 600RR (in reply to spencerjw) Post #: 2

RE: 98 plastics on a 92 F2 - 7/3/2006 1:00:08 AM    spencerjw Posts: 113 Joined: 6/25/2006 Status: offline From working with the bike and doing routine maintenance does it seem all the bolts fit in the general areas or can you tell if there was any work done to make things fit correctly? Are all the parts from a 98 or only certain ones? From what I can tell in your pics it looks as though the lower cowel is extremly simular to the 92 and the upper is damn close with the exception of the turn signals not being part of the cowel itself. And there's an extra vent in your lower cowell right above your "Honda" decal. The side cowel with the vents below the seat also looks like the 92 but the tail itself definetly looks like the 98. < Message edited by spencerjw -- 7/3/2006 1:01:17 AM > _____________________________ Spencer '92 Honda CBR 600 F2 (in reply to Nick I.) Post #: 3

RE: 98 plastics on a 92 F2 - 7/4/2006 1:28:59 AM    Nick I.   Posts: 181 Joined: 3/30/2006 From: Delco Pa. Status: offline yes everything seems to go where it is supposed to, the bike was low sided on both sides when i bought it, so some of the tabs are bent in. but it fits fine, the access panels fit a little snug because the middle piece hits the radiator slightly. that is about it. yes that is a cut out above the honda sticker. _____________________________ 1993 F2 - 1998 Plastic. Sold! The Replacement 2003 600RR (in reply to spencerjw) Post #: 4

RE: 98 plastics on a 92 F2 - 7/4/2006 8:06:25 AM    Syphen Posts: 341 Joined: 4/29/2006 Status: offline So everything on your bike is 98 plastic? including the upper and tail? F2 tank though right? _____________________________ 1992 CBR250RR "BabyBlade" & 2000 CBR600 F4 (in reply to Nick I.) Post #: 5

RE: 98 plastics on a 92 F2 - 7/4/2006 10:50:47 PM    Nick I.   Posts: 181 Joined: 3/30/2006 From: Delco Pa. Status: offline Yes the tank is the original 93 F2. Everything painted RED is 98. the tail pieces I got off of EBAY, I don't remember what they are from, but they line up perfectly. I would imagine they are F2 though. _____________________________ 1993 F2 - 1998 Plastic. Sold! The Replacement 2003 600RR (in reply to Syphen) Post #: 6

RE: 98 plastics on a 92 F2 - 7/4/2006 11:56:09 PM    spencerjw Posts: 113 Joined: 6/25/2006 Status: offline So does anyone know if there were any body plastic difference between the years that the F2 was produced? _____________________________ Spencer '92 Honda CBR 600 F2 (in reply to Nick I.) Post #: 7

Today's Posts
Most Active Topics
Make A Donation
Forum Rules & FAQ
RSS Feeds

Top 10 Posters
voodoochyl 7459 doncollins 6282 tahoe sc 5915 rrasco 5747 tk954rr 5366 pitsvtec 5323 thex 5301 d2vw14_20 5166 vp 4940 chainstretch 4835

New Vendors
AMSOIL - Performance Oil Technology
AMSOIL - Performance Oil Technology